Hab mal Bios Abgetippt....
Nichts falsches denken... [4X4X32] is mein Alter brenner... hab ma zum überprüfen angeschlossen, ob nich fehlererkennung bei meinem lg gsa 4040 falsch tut...
MEINE BIOS EINSTELLUNGEN (Gigabyte GA 7NNXP)
=============================================
CMOS Setup Utility - Copyright (c) 1984-2003 Award Software
------------------------------------------------------------
> Standart CMOS Features | > Frequency/Voltage Control
> Advanced BIOS Features | Load Fail-Safe
> Advanced Chipset Features| Load Optimized Defaults
> Integrated Perpherals | Set Supervisor Passwort
> Power Management Setup | Set User Passwort
> PnP/PCI Configurations | Save & Exit Setup
> PC Health Status | Exit Without Saving
------------------------------------------------------------
> Standart CMOS Features
========================
...uniterressant...
Datum, Zeit,
IDE Primary Master [NONE]
IDE Primary Slave [NONE]
IDE Secondary Master [4X4X32]
IDE Secondary Slave [NONE]
Floppy... bla bla
> Advanced BIOS Features
========================
BIOS Flash Prtection [AUTO]
First Boot Device [CDROM]
Second Boot Device [SCSI]
Third Boot Device [Floppy]
SATA/RAID/SCSI Boot Order [RAID]
Boot up Floppy Seek [Disabled]
Bot up Num-Lock [ON]
Passwort Check [Setup]
Interrup Mode [APIC]
HDD S.M.A.R.T. Capability [Disabled]
Flexible AGP 8X [Auto]
Init Display First [AGP]
AGP Aperature Size (MB) [64M]
> Advanced Chipset Features
===========================
FSB, RAM Timings...
> Integrated Perpherals
=======================
On-Chip Primary PCI IDE [Enabled]
Primary Master UDMA [Auto]
Primary Slave UDMA [Auto]
On-Chip Secondary PCI IDE [Enabled]
Secondary Master UDMA [Auto]
Secondary Slave UDMA [Auto]
IDE1 Conductor Cable [Auto]
IDE2 Conductor Cable [Auto]
USB Host Controler [V1.1+V2.0]
USB Keyboard Support [Enabled]
USB Mouse Support [Enabled]
AC97 Audio [Auto]
On-Chip LAN (nVIDIA) [Auto]
Machine MAC(NV) Address [Disabled]
x MAC(NV) Address Input Press Enter (nicht anwählbar; nicht aktiv...)
On-Chip 1394 [Auto]
Onboard H/W Serial ATA [Disabled]
x Serial ATA Funktion RAID (nicht anwählbar; nicht aktiv...)
Onboard H/W RAID [Enabled]
GigaRAID Funktion [RAID]
Onboard GigaBit LAN [Enabled]
GigaBit LAN Boot ROM [Disabled]
Onboard LAN BOOT ROM [Disabled]
Onboard Serial Port 1 [3F8/IRQ4]
Onboard Serial Port 2 [2F8/IRQ3]
UART Mode Select [Normal]
x UR2 Duplex Mode Half (nicht anwählbar; nicht aktiv...)
Onboard Parallel Port [358/IRQ7]
Parallel Port Mode [ECP]
ECP Mode Use DMA [3]
Game Port Address [201]
Midi Port Address [330]
Midi Port IRQ [10]
CIR Port Address [Disabled]
x CIR Port IRQ 11 (nicht anwählbar; nicht aktiv...)
> Power Management Setup
========================
Einschalten bei LAN, Urzeit... bla bla bla
> PnP/PCI Configurations
========================
Resources Controlled by [Auto]
x IRQ Resources Press Enter (nicht anwählbar; nicht aktiv...)
PCI1/5 IRQ Assignement [Auto]
PCI2 IRQ Assignement [Auto]
PCI3 IRQ Assignement [Auto]
PCI4 IRQ Assignement [Auto]
> PC Health Status
==================
Temperaturen, Voltage Anzeige, FAN Speed
> Frequency/Voltage Control
===========================
VCORE, DIMM, AGP, CPU voltage und ratio control...
sieht in editor->gerade' aus...
Wie Angeschlossen???
IDE 3 ----------ATA133 Kabel---------HDD1 auf cs
IDE 4 ----------ATA133 Kabel---------HDD2 auf cs
was ich noch gemacht hab
2mal treiber auf diskette (1x gigabyte cd, 1x internet)
festplatten formatiert
fast mein computer zum fenster raus geworfen... *g*